GE Ultrasound Equipment Cleaning and Disinfection Guidelines

• Before cleaning and disinfecting the machine, please turn off the device and disconnect the power cable.

• It is recommended to use the recommended cleaning and disinfection materials and solutions.

•  

• Do not use thinners, benzene, ethanol, methanol, scouring agents, or other strong solvents; they will damage the cabinet or display panel. Isopropyl alcohol should not be used without instructions.

• Do not steam sterilize or high-temperature sterilize equipment components.

• Do not scratch or press the panel with sharp objects (e.g., pencils or pens), as this may damage the panel.

• The cleaning and disinfection temperature should not exceed 60°C.

   

• Operation panel and main display and touch panel 

• Keyboard and monitor frame 

• Probe holder 

• Machine housing, front and rear handles, and imaging switch

• Probe

• Puncture stand (if applicable)

• Isopropyl alcohol approximately 70% 

• Disposable sterilizing cloth: Kava cloth (Ingredients: Quaternary ammonium compound + isopropyl alcohol)

• Quaternary ammonium compound + Polyhexamethylene guanidine hydrochloride SONO ultrasound wipes (Ingredients: Quaternary ammonium compound)

• 3% hydrogen peroxide; 10% bleach solution (10% bleach, 90% water)

• 75% ethanol solution is used for soaking, scrubbing, and disinfection, primarily for hand skin disinfection.

• 70% isopropyl alcohol solution is used for soaking, scrubbing, and disinfecting medical equipment and medical facilities.

• The host equipment should be cleaned regularly. After turning off the power, use a soft damp cloth to wipe the display, touch screen, operation panel, probe bracket, and machine housing.

• If the machine surface has blood stains, oil stains, or other dirt, a dust-free soft cloth can be used to wipe with a small amount of isopropyl alcohol. When wiping, be careful not to let the liquid flow into the gaps of the display or operation panel/touch screen. Finally, wipe it dry with a dry cloth.

• Remove the air filter at least every two weeks, clean it with a vacuum cleaner, or rinse it with clean water, dry it, and then reinstall it in the machine.

• Wet a sterile cloth with a liquid disinfectant, or apply disinfectant wipes, to moisten the machine surface. Do not press hard on the wipes, to prevent liquid from entering the gaps and crevices of the console.

• Keep the surface moist for the applicable contact time. If the surface does not remain moist throughout the contact time, apply additional disinfectant as needed to extend the wetting time.

• After the contact time is up, clean up excess liquid with a dry sterile cloth. To avoid disinfectant accumulation, or to remove disinfectants that may irritate the skin, a sterile damp cloth can be used for the cleaning step.

• To avoid disinfectant accumulation, or to remove disinfectants that may irritate the skin, a sterile damp cloth can be used for the cleaning step.

• Flat ultrasound screens can be wiped with medical isopropyl alcohol disinfecting wipes with a concentration of no more than 70%.

• Plasma sterilizers with sufficient power to cover the environment can be selected for department sterilization.

• When using ultraviolet environmental disinfection, the probe should be stored in a box and the equipment should be covered with velvet.

This information is sourced from the internet. Please contact us for removal if there is any infringement.

• Before cleaning and disinfecting the machine, please turn off the device and disconnect the power cable.

• It is recommended to use the recommended cleaning and disinfection materials and solutions.

•  

• Do not use thinners, benzene, ethanol, methanol, scouring agents, or other strong solvents; they will damage the cabinet or display panel. Isopropyl alcohol should not be used without instructions.

• Do not steam sterilize or high-temperature sterilize equipment components.

• Do not scratch or press the panel with sharp objects (e.g., pencils or pens), as this may damage the panel.

• The cleaning and disinfection temperature should not exceed 60°C.

   

• Operation panel and main display and touch panel 

• Keyboard and monitor frame 

• Probe holder 

• Machine housing, front and rear handles, and imaging switch

• Probe

• Puncture stand (if applicable)

• Isopropyl alcohol approximately 70% 

• Disposable sterilizing cloth: Kava cloth (Ingredients: Quaternary ammonium compound + isopropyl alcohol)

• Quaternary ammonium compound + Polyhexamethylene guanidine hydrochloride SONO ultrasound wipes (Ingredients: Quaternary ammonium compound)

• 3% hydrogen peroxide; 10% bleach solution (10% bleach, 90% water)

• 75% ethanol solution is used for soaking, scrubbing, and disinfection, primarily for hand skin disinfection.

• 70% isopropyl alcohol solution is used for soaking, scrubbing, and disinfecting medical equipment and medical facilities.

• The host equipment should be cleaned regularly. After turning off the power, use a soft damp cloth to wipe the display, touch screen, operation panel, probe bracket, and machine housing.

• If the machine surface has blood stains, oil stains, or other dirt, a dust-free soft cloth can be used to wipe with a small amount of isopropyl alcohol. When wiping, be careful not to let the liquid flow into the gaps of the display or operation panel/touch screen. Finally, wipe it dry with a dry cloth.

• Remove the air filter at least every two weeks, clean it with a vacuum cleaner, or rinse it with clean water, dry it, and then reinstall it in the machine.

• Wet a sterile cloth with a liquid disinfectant, or apply disinfectant wipes, to moisten the machine surface. Do not press hard on the wipes, to prevent liquid from entering the gaps and crevices of the console.

• Keep the surface moist for the applicable contact time. If the surface does not remain moist throughout the contact time, apply additional disinfectant as needed to extend the wetting time.

• After the contact time is up, clean up excess liquid with a dry sterile cloth. To avoid disinfectant accumulation, or to remove disinfectants that may irritate the skin, a sterile damp cloth can be used for the cleaning step.

• To avoid disinfectant accumulation, or to remove disinfectants that may irritate the skin, a sterile damp cloth can be used for the cleaning step.

• Flat ultrasound screens can be wiped with medical isopropyl alcohol disinfecting wipes with a concentration of no more than 70%.

• Plasma sterilizers with sufficient power to cover the environment can be selected for department sterilization.

• When using ultraviolet environmental disinfection, the probe should be stored in a box and the equipment should be covered with velvet.

This information is sourced from the internet. Please contact us for removal if there is any infringement.

• Before cleaning and disinfecting the machine, please turn off the device and disconnect the power cable.

• It is recommended to use the recommended cleaning and disinfection materials and solutions.

•  

• Do not use thinners, benzene, ethanol, methanol, scouring agents, or other strong solvents; they will damage the cabinet or display panel. Isopropyl alcohol should not be used without instructions.

• Do not steam sterilize or high-temperature sterilize equipment components.

• Do not scratch or press the panel with sharp objects (e.g., pencils or pens), as this may damage the panel.

• The cleaning and disinfection temperature should not exceed 60°C.

   

• Operation panel and main display and touch panel 

• Keyboard and monitor frame 

• Probe holder 

• Machine housing, front and rear handles, and imaging switch

• Probe

• Puncture stand (if applicable)

• Isopropyl alcohol approximately 70% 

• Disposable sterilizing cloth: Kava cloth (Ingredients: Quaternary ammonium compound + isopropyl alcohol)

• Quaternary ammonium compound + Polyhexamethylene guanidine hydrochloride SONO ultrasound wipes (Ingredients: Quaternary ammonium compound)

• 3% hydrogen peroxide; 10% bleach solution (10% bleach, 90% water)

• 75% ethanol solution is used for soaking, scrubbing, and disinfection, primarily for hand skin disinfection.

• 70% isopropyl alcohol solution is used for soaking, scrubbing, and disinfecting medical equipment and medical facilities.

• The host equipment should be cleaned regularly. After turning off the power, use a soft damp cloth to wipe the display, touch screen, operation panel, probe bracket, and machine housing.

• If the machine surface has blood stains, oil stains, or other dirt, a dust-free soft cloth can be used to wipe with a small amount of isopropyl alcohol. When wiping, be careful not to let the liquid flow into the gaps of the display or operation panel/touch screen. Finally, wipe it dry with a dry cloth.

• Remove the air filter at least every two weeks, clean it with a vacuum cleaner, or rinse it with clean water, dry it, and then reinstall it in the machine.

• Wet a sterile cloth with a liquid disinfectant, or apply disinfectant wipes, to moisten the machine surface. Do not press hard on the wipes, to prevent liquid from entering the gaps and crevices of the console.

• Keep the surface moist for the applicable contact time. If the surface does not remain moist throughout the contact time, apply additional disinfectant as needed to extend the wetting time.

• After the contact time is up, clean up excess liquid with a dry sterile cloth. To avoid disinfectant accumulation, or to remove disinfectants that may irritate the skin, a sterile damp cloth can be used for the cleaning step.

• To avoid disinfectant accumulation, or to remove disinfectants that may irritate the skin, a sterile damp cloth can be used for the cleaning step.

• Flat ultrasound screens can be wiped with medical isopropyl alcohol disinfecting wipes with a concentration of no more than 70%.

• Plasma sterilizers with sufficient power to cover the environment can be selected for department sterilization.

• When using ultraviolet environmental disinfection, the probe should be stored in a box and the equipment should be covered with velvet.

This information is sourced from the internet. Please contact us for removal if there is any infringement.

• Before cleaning and disinfecting the machine, please turn off the device and disconnect the power cable.

• It is recommended to use the recommended cleaning and disinfection materials and solutions.

•  

• Do not use thinners, benzene, ethanol, methanol, scouring agents, or other strong solvents; they will damage the cabinet or display panel. Isopropyl alcohol should not be used without instructions.

• Do not steam sterilize or high-temperature sterilize equipment components.

• Do not scratch or press the panel with sharp objects (e.g., pencils or pens), as this may damage the panel.

• The cleaning and disinfection temperature should not exceed 60°C.

   

• Operation panel and main display and touch panel 

• Keyboard and monitor frame 

• Probe holder 

• Machine housing, front and rear handles, and imaging switch

• Probe

• Puncture stand (if applicable)

• Isopropyl alcohol approximately 70% 

• Disposable sterilizing cloth: Kava cloth (Ingredients: Quaternary ammonium compound + isopropyl alcohol)

• Quaternary ammonium compound + Polyhexamethylene guanidine hydrochloride SONO ultrasound wipes (Ingredients: Quaternary ammonium compound)

• 3% hydrogen peroxide; 10% bleach solution (10% bleach, 90% water)

• 75% ethanol solution is used for soaking, scrubbing, and disinfection, primarily for hand skin disinfection.

• 70% isopropyl alcohol solution is used for soaking, scrubbing, and disinfecting medical equipment and medical facilities.

• The host equipment should be cleaned regularly. After turning off the power, use a soft damp cloth to wipe the display, touch screen, operation panel, probe bracket, and machine housing.

• If the machine surface has blood stains, oil stains, or other dirt, a dust-free soft cloth can be used to wipe with a small amount of isopropyl alcohol. When wiping, be careful not to let the liquid flow into the gaps of the display or operation panel/touch screen. Finally, wipe it dry with a dry cloth.

• Remove the air filter at least every two weeks, clean it with a vacuum cleaner, or rinse it with clean water, dry it, and then reinstall it in the machine.

• Wet a sterile cloth with a liquid disinfectant, or apply disinfectant wipes, to moisten the machine surface. Do not press hard on the wipes, to prevent liquid from entering the gaps and crevices of the console.

• Keep the surface moist for the applicable contact time. If the surface does not remain moist throughout the contact time, apply additional disinfectant as needed to extend the wetting time.

• After the contact time is up, clean up excess liquid with a dry sterile cloth. To avoid disinfectant accumulation, or to remove disinfectants that may irritate the skin, a sterile damp cloth can be used for the cleaning step.

• To avoid disinfectant accumulation, or to remove disinfectants that may irritate the skin, a sterile damp cloth can be used for the cleaning step.

• Flat ultrasound screens can be wiped with medical isopropyl alcohol disinfecting wipes with a concentration of no more than 70%.

• Plasma sterilizers with sufficient power to cover the environment can be selected for department sterilization.

• When using ultraviolet environmental disinfection, the probe should be stored in a box and the equipment should be covered with velvet.

This information is sourced from the internet. Please contact us for removal if there is any infringement.